Intel D50DNP1MHCPAC Server System UEFI BIOS/Firmware R01.01.0004

Versions:

- System BIOS -SE5C741.86B.01.01.0004
- ME Firmware -06.00.04.0033
- BMC Firmware -1.53
- FRU -0.07
- CPLD -v4p0
- sysfwupdt.efi - Version 16.0.8

BIOS Changes:

- Hsd-es: NA [DSG] Change BIOS ID to SE5C741.86B.01.01.0004. This release is mapping to RP release Reference code version: EGLSTRM.0.RPB.9409.P.28

BMC Changes:

- Defect: [15013024578] [EGS][CCB3768] Get VROC software key level via 0x30 0x9d should be restricted to KCS channel and only available in POST phase (#186)" (#188)
- Defect: PSU Fan Speed 2 sensor has no reading with the 2100W Titanium PSU
- Defect: The ipmid command cannot be executed during the execution of the dump-jounal script.
- Defect: [15012885574] Sensor warning triggered on PVC when reading is 0
- Defect: [15013036205] During BMC reset stress test, BMC automatically downgraded to backup version.
- Defect: [2103657375] EWS customization bin file cannot be updated successfully.
- Feature: Only update CBB retimer 1.27.12 for DNP SDP image
- Feature: [DNP] CBB retimer fw update to 1.27.12 (#69)" (#71)

CPLD Changes:

1. Version change to 0x28 DNP v4p0), mailbox and SGPIO.
2. SVN value is 0x02 for Debug Signed (mailbox 0x02), 0x08 for Production Signed. ROT vlaue is 0x02 for EagleStream PLATFORM (mailbox 0x03), 0x01 for Whitley.
3. Add/remove spi whitelist.01h/35h/B1h/B5h add to whitelsit; 35h/B1h remove to forbidden list. spi_filter.sv [2103657177] System don't power on automatically if set "Power on" in BIOS setting "Resume on AC power loss" with Winbond BMC SPI flash.
4. Remove RP code 475p4, about WDT recovery/implementing FIFO for IBB/OBB checkpoints which are related to Bios rollback conditions.

FRU Changes:

- Change sysfwupdt.efi to 16.0.8
- Keep chassis/board/product info length to support maximum 32-byte-lenght data for field
- Change template field content back to 0.05

GENERAL INSTALLATION PROCEDURE:

1. Unzip the contents of the update package and copy all files to the root directory of a removable media (USB flash drive)
2. Insert the USB flash drive to any available USB port on the system to be updated
3. Power on the server and boot into uEFI shell
4. Access to the USB flash drive inserted and begin the update process running the Startup.nsh
5. Once BIOS update process has successfully completed, system will reboot automatically and will take around 13 minutes with the screen off and ID Led (Blue light) ON, once the ID and SYSTEM LED are off, the server will power on automatically.
6. After first reboot and post screen, the server could be rebooted a second time.

Verifying Updates:

01. After the final update has completed successfully, reboot the system
02. During POST, hit the <F2> Key when prompted to access the BIOS Setup Utility
03. At the main menu verify the BIOS revision is correct
04. Move cursor to the SERVER MANAGEMENT menu and hit Enter
05. Move cursor to the SYSTEM INFORMATION Option and hit Enter
06. Verify the BMC Firmware revision is correct
07. Verify the ME Firmware revision is correct
08. Configure desired BIOS Option settings
09. Hit the F10 Key to Save Changes and Exit

UEFI sysfwupdt:

1. Power on system, press F2 enter BIOS setup and goto Main > PFR page, set PFR provision to enable.
2. Press F10 to save and reboot.
3. During POST, press F2 to enter BIOS setup again, goto Main > PFR page, PFR Provision change to grey and can't be chosen, PFR Provision Status change to Provisioned.
4. Copy the entire contents of the IWFI package to the HDD or USB flash drive. (All of the files in the package must reside in the same directory.)
5. Boot to UEFI Shell, then change the Shell to mapped device file system Example: Shell> fs0: (or fs1:)
6. Run UpdBIOS_FCP.nsh (or startup.nsh to full installation of the SUP).).
7. Reboot system after the update is completed.
8. Do NOT interrupt the BIOS POST during the first boot.

BMC

 Web Console update:
1. Open BMC Web Console and login
2. Go to Configuration > BIOS/IFWI Firmware Update
3. if desired select Recovery and/or Reset Immediately checkboxes
4. Choose the File (XXX_EBG_SPR_UpdateCapsule_prd.bin)
5. Upload
6. BIOS will be updated on the next reboot (if Reset Immediately checkbox was not selected).
7. Do NOT interrupt the BIOS POST during the first boot.

FRUSDR INSTALLATION:

1. Ensure BMC FW release v1.36-0 or later is pre-installed before attempting this FRU update.
2. Copy all of the files and directories of this zip to a USB key
3. Execute the following script to bring up the main FRU load menu: UpdFRU_FCP.nsh
4. If want to direct update FRU without prompt selection:fru_update_noprompt.nsh

About Firmware Updates:

Applying a newer firmware version than the one already installed on your unit can bring various enhancements, include workarounds for diverse problems encountered by the device, and improve or add newly developed features.

On the other hand, downgrading the firmware version can recover the device's functionality in the event of a software update either turning up faulty or causing the unit's overall performance to drop. However, bear in mind that applying an older firmware isn't recommended and might not always be possible.

When it comes to the update steps, due to the large variety of devices and numerous ways for installing a new firmware, it is recommended that you carefully read and understand the upgrade steps, and consider applying a different firmware only when you have familiarized yourself with the update method.

As the installation process is most of the times quite risky, this step should be taken by users that have the ability to successfully complete the update; regular users may initiate it at their own risk. Moreover, it's best that this task be performed in a steady power environment such as the one ensured by a UPS unit.

Therefore, if you consider applying this release, hit the download button, take into account all the aforementioned aspects, and update the device's firmware. Also make sure you constantly check with our website to ensure that you don't miss a single new release.