NETGEAR PTV3000 WiDi Adapter Firmware 2.4.03

Supported Miracast platforms:

- Samsung Galaxy S3 (Android 4.1.1 or above)
- Samsung Galaxy S4
- Samsung Galaxy Note II
- Samsung Galaxy Note 10.1
- LG Optimus G (Android 4.0.4 or above)
- Google Nexus 4 (Android 4.2.1)
- Sony Xperia (various models with Android 4.0.4 or above)

Enhancements & Bug Fixes:

- Debug mode to display additional error messages.
- Samsung Corrected User Agent to be SEC-WDH/LH01 for better Samsung TCP (movie mode) compatibility.
- Fixed an additional case that was causing the video output to fail from certain laptops.
- (Dell XPS Mod#P11F, Win7 HP x64, i7-26020M, 4GB DDR3, Centrino Advanced-N 6230 driver v15.7, HD Graphics 3000 driver v.8.15.10.2661
- P2TV3000, hardware v.2.0.0, fw v.2.3.7 Widi 4.0.18)
- Adapter name is not changed after rebooting device without disconnecting from WiDi app first.
- Overscan value was not cleared on factory reset.
- Pushbuttons now disconnect currently running sessions.
- No UI animation in connecting screen yet. It will cause UI to hang.
- Not timing out after canceling Connection from Legacy WiDi.
- Not Connecting Using WiDi 2.2 and 3.0 with FW v.2.3.7 - Only with certain laptop.
- All remaining strings translated.
- AV Sync issue vs Motorola phones. A/V interleaving has been analyzed (14515MBr12558_ENG_netgear_IHS).
- Not all audio channels have good quality. The latest Intel KPI report @ 14506 showed this as passing.
- Default overscan value set to 10. To verify this, need to reset to factory defaults first.
- Fixed issue that device displays new PIN code while PC/WiDi app is still in "connecting" state and did not come up with dialog box to allow PIN entry.
- Fixed Widi issue that device cannot connect to PC when Widi app on PC is set to speed mode.
- Enables association retry after associate reject when connection fails.
- Fixed wifi driver issue to enable disconnect event when there is no beacon from PC when PC is the GO.
- Fixed connectivity issue with Toshiba laptop when working in a noisy wifi environment.
- Fixed Widi L2SD connectivity issue.
- Change SSID to "Direct-xx-PTV" when PTV is the GO.
- Properly enables HDCP2.1 and HDCP2.0 interface.
- Fixed issue that WiDi app status shows "Connected", device stays in "Connecting...." state forever. Timeout is enabled, worst case 2 min.
- Allow Nexus 4 to run in 2.4Ghz when Nexus 4 is not associated with any AP.
- Fixed issue of widi connection if it is right after association with Sony Xperia mobile phone.
- Fixed Widi issue that fast cursor is off by a few pixels.
- Fixed connectivity issue with BCM4352 and BCM43241 wifi controller. (Device is already compatible with Intel 11ac, N7260).
- PTV3000 didn't get ack from invitation response but no retry to resend and the invitation response send from PTV3000 indicate failure.
- Dongle becomes unscannable after 10 hours with L2SD scan off.
- Provisional Discovery incorrectly causes PIN to be displayed.
- Nexus 4 Android 4.2.2 abruptly disconnects while streaming. Includes new QCA driver 3.2.1.122.
- [Google Nexus] RTSP UDP port seems to open successfully, but data transmission fails.
- Allow screen size adjustment on Miracast screens. See updated files in www/ (index.html and configure_overscan.sh).
- [Miracast] PTV 3000 sometimes could not be discovered at the first try.
- Inconsistency between probe response (20Mhz) and capability beaconed (20Mhz & 40Mhz) when PTV is acting as a GO.
- Throughput improved roughly 10% by disabling UDP checksum.
- Excessive frame repeats and skips [PARTIAL] #333 and #329 improve this, but needs to tested against Intel KPI.
- Support passing EDID to source unmodified.
- Fixed issue of "Push2TV" SSID not properly enabled when in FW update more. Fixed wpa_supplicant not being properly removed when switching to "Settings Mode".
- Fixed issue with device stuck in "connecting" state forever. Another fix applied that handles a case where a failure in IP address acquisition could cause the UI to be stuck in "Connecting…".
- Fixed the PTV not connecting with HSW+Broadcom SDIO. Adjusted default association timeout to 15 seconds from 5 seconds, as well as reduced the timeout for a scheduled scan from 5 seconds to 3 seconds. These changes fit within the timings for the source laptops times before it gives up.
- Fixed issue on connectivity with Samsung GS3. Applied patch from QCA that reduces connection retry times and checks for false PBC overlap conditions.
- Fixed provision discovery issue. Provisional Discovery incorrectly causes PIN to be displayed (partial fix). GO Negotiation with PIN is not presenting properly.
- Fixed issue that PIN pairing fails occasionally (Win Blue + 6235 WiFi).
- Fixed issue that Dongle becomes non discoverable after failed invitation attempt.
- Fixed issue that fresh pairing is inconsistent from IvyBridge+N-6235 on WiDi 4.1.17.0+15.4.1.1. Dongle tries to associate before windows blue laptop is ready for wps. This leads to connection failure.
- Fixed issue that Audio does not work with WiDi 4.x Low Delay mode.
- Fixed a number of Web UI issues.
- Change default to Auto-PBC on. (Auto-PBC and L2SD on/off can both be configured from the web UI).
- String modifications.