Fixes:
- When the switch is in the default config, if we set the service-control http 23 30, the DUT will crash since command parsed error.
- When using SNMPc to view the dot1agCfmMepDbTable (OID: 1.3.111.2.802.1.1.8.1.7.3), DUT will crash
- When uploading firmware using ftp from in-band, and write memory 1 at the same time, DUT will crash.
- When send error packet to DUT, we cannot see error count at UI(Web, CLI) after link down this port.
- Memory leak due to send fault trap but not free.
- IP mac move will cause the Ping process fail when linking to two devices with same IP and MAC.
- Disable arp-learning mode but DUT disable wrong port
- In spanning tree + static trunk environment, the host’s mac will be learned to wrong port.
- In Web, when set Queues weight over range, the warning message is incorrect.
- In Web, when setting MRSTP port path cost to invalid value, the error message shows error
- When igmp-snooping querier is disabled, if the DUT receives a general query with smaller IP than DUT, DUT will periodicity sends out general query after DUT's querier port timeout.
- In web set subnet-based VLAN entry with multicast or reserved IP address, write memory, restore config, DUT pop error message.
- Device crash when backup huge configuration to TFTP server via SSH version 1
- Doing fiber port link down/up overnight test, DUT crash
- When system log is full, every newly add log will add a table full log into errlog.
- Switch does not do mac move in arp-request mode.
- Power off when system is booting and then reboot the system, will put all port into inactive status in show running and the user config dispear.
- ALARM LED cannot keep turn ON after HTP burn in test is failed.
- If the management address type of remote machine is ipv6, management address of "show lldp info remote interface port-channel" will be abnormal format (mac-address format)
- Clear some warning on .mib for MIB management tool of what’s up
- ITS (UK): GS2200-24 stop forwarding multicast traffic and loss of management, also the console no response.
- [Web] ARP table’s item will display error when user using web arp table’s port flush
- [ipv6] upload the wrong firmware version (upload GS2200-24P’s firmware to GS2200-8HP) will cause DUT crash
- [Auto]When run the automation scipt, DUT will crash.
- Fix “show tech-support” hang
- DUT sends two or more different LLDP packets on the same port.
- Normal reboot (warm start) will clear the stack information of crash in the debug area
- [Web] User cannot access the error.html when configuration is wrong via ipv6 link-local address on Windows XP.
- [Web] User cannot upgrade firmware via ipv6 link-local address on Windows XP and will cause huge memory leak in this environment
- When the switch is in the default config, if we set the service-control http 23 30, the DUT will crash since command parsed error.
- When using SNMPc to view the dot1agCfmMepDbTable (OID: 1.3.111.2.802.1.1.8.1.7.3), DUT will crash
- When uploading firmware using ftp from in-band, and write memory 1 at the same time, DUT will crash.
- When send error packet to DUT, we cannot see error count at UI(Web, CLI) after link down this port.
- Memory leak due to send fault trap but not free.
- IP mac move will cause the Ping process fail when linking to two devices with same IP and MAC.
- Disable arp-learning mode but DUT disable wrong port
- In spanning tree + static trunk environment, the host’s mac will be learned to wrong port.
- In Web, when set Queues weight over range, the warning message is incorrect.
- In Web, when setting MRSTP port path cost to invalid value, the error message shows error
- When igmp-snooping querier is disabled, if the DUT receives a general query with smaller IP than DUT, DUT will periodicity sends out general query after DUT's querier port timeout.
- In web set subnet-based VLAN entry with multicast or reserved IP address, write memory, restore config, DUT pop error message.
- Device crash when backup huge configuration to TFTP server via SSH version 1
- Doing fiber port link down/up overnight test, DUT crash
- When system log is full, every newly add log will add a table full log into errlog.
- Switch does not do mac move in arp-request mode.
- Power off when system is booting and then reboot the system, will put all port into inactive status in show running and the user config dispear.
- ALARM LED cannot keep turn ON after HTP burn in test is failed.
- If the management address type of remote machine is ipv6, management address of "show lldp info remote interface port-channel" will be abnormal format (mac-address format)
- Clear some warning on .mib for MIB management tool of what’s up
- ITS (UK): GS2200-24 stop forwarding multicast traffic and loss of management, also the console no response.
- [Web] ARP table’s item will display error when user using web arp table’s port flush
- [ipv6] upload the wrong firmware version (upload GS2200-24P’s firmware to GS2200-8HP) will cause DUT crash
- [Auto]When run the automation scipt, DUT will crash.
- Fix “show tech-support” hang
- DUT sends two or more different LLDP packets on the same port.
- Normal reboot (warm start) will clear the stack information of crash in the debug area
- [Web] User cannot access the error.html when configuration is wrong via ipv6 link-local address on Windows XP.
- [Web] User cannot upgrade firmware via ipv6 link-local address on Windows XP and will cause huge memory leak in this environment
- CATEGORY:
- Router / Switch / AP
- COMPATIBLE WITH:
- OS Independent
- file size:
- 2.3 MB
- filename:
- GS2200-8_4.00(AAAV.3)C0.zip
Other versions
OS Independent