Peplink SpeedFusion Engine HW1 Router Firmware 8.1.3

Improvements:

- [B20] Added: Supporting of MAX Adapter
Compatible with Balance: 20/30

- [AP Controller / 11ac] Added: When a Wi-Fi client is connected to/disconnected from an AP, the client's name will be shown in the Event Log.
Compatible with Balance: All
Compatible with MAX: BR1 MK2, 700, HD2/4, Transit
Compatible with MediaFast: All
Compatible with X Series: EPX, SDX Pro, SDX, 580X, 380X, PDX, MBX, 20X
Compatible with Surf SOHO: SOHO MK3

- [DPI] Updated: 269 protocols can now be identified in the "Active Sessions" and "DPI Reports" on InControl 2
- [BGP] Added: BGP over GRE
Compatible with All Models

- [Cellular & LTE-US] Added support for 3G sunset of AT&T
Compatible with Models with integrated LTE-US Cellular

- [FusionHub] Added: BGP/OSPF/RIP2 Support
Compatible with usionHub

Resolved Issues:

- [FusionHub] Fixed: When Web Content Filtering was enabled, system CPU load would become unnecessarily higher, and extra downlink traffic would be consumed.
- [FusionHub] Fixed: Abnormal CPU load
Compatible with FusionHub

- [Jumbo Frame & Link Aggregation] Fixed: "HA Configuration Sync" did not work if "Jumbo Frame" and "Link Aggregation" on LAN was enabled
Compatible with Balance: 305, 380 or above
Compatible with MediaFast: 500, 750
Compatible with X Series: EPX, SDX Pro, SDX, 580X, 380X

- [System] Fixed: Potential system instability issue
- [System] Fixed: Unable to apply a large amount of Geolocation Firewall rules
Compatible with All Models

- [EPX] Fixed: Cellular WAN shows "Unknown Physical Status" if the device had more than ten cellular WANs
Compatible with X Series: EPX

- [B310 5G] Fixed: Unable to show LAN port status
Compatible with Balance: 310 5G/Fiber 5G

- [5G] Fixed: Cellular WANs that configured to connect in "LTE Only" connected in 5G mode
Compatible with Balance: 310 5G/Fiber 5G
Compatible with X Series: EPX, MBX, SDX Pro, SDX, 310X

- [AP Controller] Fixed: AP > Mesh / WDS Page becomes unresponsive
Compatible with Balance: All
Compatible with MAX: 700, HD2/4, Transit
Compatible with MediaFast: All
Compatible with X Series: EPX, SDX Pro, SDX, 580X, 380X, PDX, MBX

- [B20X] Fixed: System instability caused by memory handling
- [B20X] Fixed: Wi-Fi clients may not connect to the 2.4 GHz Wi-Fi radio
Compatible with X Series: 20X

- [Wi-Fi] Fixed: Wi-Fi FragAttack Vulnerability
Compatible with Balance: 30 Pro, One
Compatible with MAX: All (Exclude: BR1 ENT, HD2 Mini, HD1/2 Dome)
Compatible with MediaFast: HD2/4
Compatible with X Series: PDX, MBX, 20X
Compatible with UBR: UBR LTE
Compatible with Surf SOHO

- [PrimeCare] Fixed: PrimeCare expiration handling malfunction
Compatible with Device product code with the suffix "-PRM"

- [SOHO MK3] Fixed: Wi-Fi clients might not connect to the 2.4 GHz Wi-Fi radio
Compatible with Surf SOHO: SOHO MK3

- [BR1 Mini] Fixed: WAN as LAN feature does not work
Compatible with MAX: BR1 Mini/Mini Core

- [310 Fiber 5G | Transit] Fixed: "Wi-Fi" LED blink when Wi-Fi AP is OFF
Compatible with Balance: 310 Fiber 5G
Compatible with MAX: Transit

- [Cellular] Fixed: Cellular radio may not connect if the "Manual carrier selection / PLMN list" setting was configured
Compatible with Balance: 30 LTE/Pro, 310
Compatible with 5G/Fiber 5G
Compatible with MAX: BR1/2, HD2/4, Transit
Compatible with UBR: UBR LTE
Compatible with MediaFast: HD2/HD4
Compatible with X Series: All

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn't either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn't be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don't always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you're looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don't power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don't miss the update that will improve your device.