Important Notices:
- SSLv3 POODLE Vulnerability (CVE-2014-3566) Addressed: A vulnerability in the design of SSLv3 has been made public. Firmware 6.2 addresses this vulnerability.
- Layer 2 PepVPN Profiles Need Reconfiguration: Layer 2 PepVPN is now easier to use and more flexible. However, PepVPN profiles created using Firmware 6.1 or below will need to be reconfigured in order to work in Firmware 6.2.
- Adjustment Needed for AP One AC Mini: In order for clients to connect to the AP One AC Mini using 802.11ac, you will need to make a slight adjustment. Please go to the Web UI and navigate to AP > Profiles > *your profile*. There, find the “5Ghz channel bonding” setting and change it to “auto”.
- PepVPN Will Appear Offline on Router Utility Version 1.3: For devices running Firmware 6.2, Router Utility 1.3 will incorrectly show PepVPN connections as offline. This can be addressed by upgrading to Router Utility version 1.4.
New Features:
PepVPN Layer 2 Peer Isolation:
- PepVPN: Isolate different clients connected to the same L2 PepVPN broadcast domain. Each device will see only themselves and headquarters.
- Navigation: Network > LAN > (?) Enable VLAN > Click LAN > (?) Enable Layer-2 bridging based PepVPN
Configurable Traffic Direction:
- PepVPN: Assign any link in a PepVPN tunnel to be upload only, download only, or both ways.
- Navigation: Network > SpeedFusion > Click Profile > WAN Connection Priority > (?) Enable Asymmetric Connection
Internal Service Forwarding:
- Routing: Intercept traffic from specified ports and forward it to a local server.
- Navigation: Network > Service Forwarding > Custom Service Forwarding Setup
Feature Improvements:
- Cellular: LTE enabled devices can now search for available networks and offer the choice of which network to connect with. This feature is available for international models with SKUs ending with “-E” (e.g. BPL-031-LTE-E)
- Cellular: Improved handling of unstable cellular connections.
- Cellular: Cellular-enabled devices can now add, remove, and modify the PIN on SIM cards.
- CLI: CLI SSH admin access can now also be restricted by source IP address.
- Firewall: Outbound firewall rules can now match by source MAC address.
- PepVPN: PepVPN profiles can now be configured to connect profiles on a first-come, first-served basis when the number of created profiles exceeds the number of peers supported.
- PepVPN: Layer 2 PepVPN is now compatible with VLAN on LAN. Options located under Network > LAN > IP Settings > Help Button.
- PepVPN: PepVPN is now more compatible with small MTU environments
- PepVPN: PepVPN Test is now showing per WAN info for easier performance analysis
- PepVPN: Bandwidth limits on PepVPN peers can now be set for both uplink and downlink.
- QoS: All devices now support bandwidth limits for individual clients.
- Routing: L2TP is now supported as WAN connection method.
- Routing: PepVPN NAT Mode has improved OSPF support. The client side can now accept routes from the server side without advertising its own network(s).
- Routing: OSPF, and all 7 load balancing algorithms are now available across all Balance and MAX models.
- Web UI: For easier access, the PepVPN Test and Analyzer is now located under Status > PepVPN (Status > SpeedFusion for devices supporting SpeedFusion).
Resolved Issues:
- Captive Portal: The Captive Portal is unable to intercept and redirect HTTPS connections to the splash page.
- Cellular: Cellular connections will auto-reset even if they have been configured to disconnect on standby.
- Cellular: Network Mode selection does not work on 3G-embedded cellular routers.
- Drop-in Mode: When Drop-in mode is enabled, dropin WAN settings cannot be saved.
- Notifications: Email notifications cannot be sent through PepVPN.
- PepVPN: PepVPN Analyzer does not work with WAN Connection Mapping
- Routing: The active sessions of LAN VLAN hosts will not show up in the "Status"->"Active Session" page.
- Routing: When using RIPv2, a connected router will remain on the list of learned routes even after the peer router has been removed.
- CATEGORY:
- Router / Switch / AP
- COMPATIBLE WITH:
- OS Independent
- file size:
- 28.4 MB
- filename:
- fw-m700_hd2-6.2.0-build2895.bin
- Newer! Peplink Pepwave MAX HD2 Router Firmware 6.3.22016-08-05
- Newer! Peplink Pepwave MAX HD2 Router Firmware 6.3.12016-02-29
- Newer! Peplink Pepwave MAX HD2 Router Firmware 6.2.22015-08-06
- Newer! Peplink Pepwave MAX HD2 Router Firmware 6.2.12015-06-29
- Peplink Pepwave MAX HD2 Router Firmware 6.22015-03-05
- Peplink Pepwave MAX HD2 Router Firmware 6.1.22014-07-30
- Peplink Pepwave MAX HD2 Router Firmware 6.1.2 Beta2014-06-06