Peplink MediaFast MFA 200 HW3 Router Firmware 8.0.2

Feature Improvements:

- [WAN] Added custom ping target setting on SmartCheck
Applies for All Models

Resolved Issues:

- [AP Controller] Unable to apply AP One Firmware 3.7 to AP units
Applies for Balance: All
Applies for MAX: 700, HD2/4, Transit
Applies for MediaFast: All
Applies for X Series: EPX, SDX, MBX

- [AP Controller] Unable to show AP Firmware 3.7.1 in Firmware Pack if External AP Management has not enabled.
Applies for Balance: All
Applies for MAX: 700, HD2/4, Transit
Applies for MediaFast: All
Applies for X Series: EPX, SDX, MBX

- [Captive Portal] Fixed an issue that causes the captive portal to display the "502 Bad Gateway" error instead.
Applies for All Models

- [Cellular & Web UI] Under the menu "Cellular Settings > Failback to Preferred SIM when...", the value of the variable "Non-preferred SIM is connected for..." cannot be set to 60 minutes or above, or else it will revert back to 1 minute.
Applies for Balance: LTE, 30 Pro
Applies for MAX: BR1/2, HD2/4, Transit
Applies for MediaFast: HD2/HD4
Applies for X Series: EPX, SDX, MBX

- [DPI] Fixed issues of DPI causing system instability.
Applies for All Models

- [Outbound Policy | Firewall Rules | IC2] Unable to push SaaS/Region Firewall & Outbound Policy Rules from InControl 2
Applies for Balance: All
Applies for MAX: All
Applies for MediaFast: All
Applies for X Series: EPX, SDX, MBX
Applies for Surf SOHO

- [Outbound Policy] The "terminate Session On Link Recovery" feature may not work if a higher Outbound Policy Rule has MAC address as Source.
Applies for All Models (Except FusionHub)

- [PepVPN] When both peers only have a single WAN, and if a WAN is unstable, PepVPN might not be
Applies for All Models

- [SDX] The front OLED panel may stop responding after setting the passcode.
Applies for X Series: SDX

- [SNMP] Fixed an issue where using both SNMP and multiple Layer 2 SpeedFusion Profiles together will cause high CPU load.
Applies for All Models

- [SpeedFusion] Fixed an issue where enabling SpeedFusion FEC causes system instability.
Applies for Balance: B210 or above
Applies forMAX: 700, HD2/4, Transit
Applies for MediaFast: All
Applies for SFE
Applies for X Series: EPX, SDX, MBX
Applies for FusionHub

- [URL Logging] Fixed an issue where the log is missing the date and time information.
Applies for All Models

- [USB WAN] If USB WAN is in use, InControl 2 may show the unit as offline.
Applies for Balance: All
Applies for MAX: BR1 ENT, HD2/4 Indoor Series
Applies for MediaFast: All
Applies for X Series: EPX, SDX, MBX
Applies for Surf SOHO

- [WAN Analysis] WAN Analysis may show "null" error during the start of the test.
Applies for All Models

- [Web UI] In rare cases, the "Apply Changes" button may be disabled after saving some changes.
Applies for All Models

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn't either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn't be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don't always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you're looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don't power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don't miss the update that will improve your device.