MikroTik RouterOS MMIPS Firmware 6.43.13

What's new in 6.43.13:

- bridge - count routed FastPath packets between bridge ports under FastPath bridge statistics;
- bridge - fixed BOOTP packet forwarding when DHCP Snooping is enabled;
- bridge - fixed packet forwarding with enabled DHCP Snooping and Option 82;
- bridge - fixed possible memory leak when using "ingress-filtering=yes" on bridge interface;
- bridge - fixed system's identity change when DHCP Snooping is enabled (introduced in v6.43);
- capsman - always accept connections from loopback address;
- certificate - force 3DES encryption for P12 certificate export;
- dhcp - fixed dual stack queue addition;
- dhcpv6-server - allow to add DHCPv6 server with pool that does not exist;
- dhcpv6-server - fixed missing gateway for binding's network if RADIUS authentication was used;
- ethernet - added "tx-rx-1024-max" counter to Ethernet stats;
- ethernet - fixed packet forwarding when SFP interface is disabled on hEX S;
- fetch - improved file downloading to slow memory;
- gps - increase precision for dd format;
- gps - removed unnecessary leading "0" for dd format;
- ipsec - fixed all policies not getting installed after startup (introduced in v6.43.8);
- ipsec - fixed stability issues after changing peer configuration (introduced in v6.43);
- ipv6 - do not allow setting "preferred-lifetime" longer than "valid-lifetime";
- kidcontrol - added "tur-fri", "tur-mon", "tur-sat", "tur-sun", "tur-thu", "tur-tue", "tur-wed" parameters;
- kidcontrol - fixed validation checks for time intervals;
- led - fixed default LED configuration for RBSXTsq-60ad;
- lldp - fixed missing capabilities fields on some devices;
- lte - do not show "session-uptime" if session is not up;
- lte - improved SIM7600 initialization after reset;
- netinstall - do not show kernel failure critical messages in the log after fresh install;
- ntp-client - fixed "dst-active" and "gmt-offset" being updated after synchronization with server;
- ppp - fixed dynamic route creation towards VPN server when "add-default-route" is used;
- rb4011 - fixed ether10 failing to auto negotiate link speed to 1Gbps;
- smb - added commenting option for SMB users (CLI only);
- smb - fixed macOS clients not showing share contents;
- smb - fixed Windows 10 clients not able to establish connection to share;
- ssh - close active SSH connections before IPsec connections on shutdown;
- supout - fixed "poe-out" output not showing all interfaces;
- supout - fixed Profile output on single core devices;
- winbox - added "conflict-detection" parameter in "IP/DHCP Server" menu;
- winbox - added "coordinate-format" parameter in LTE interface settings;
- winbox - added "use-local-address" parameter in "IP/Cloud" menu;
- winbox - allow specifying interface lists in "CAPsMAN/Access List" menu;
- winbox - fixed "IPv6/Firewall" "Connection limit" parameter not allowing complete IPv6 prefix lengths;
- winbox - fixed "LCD" menu not shown on RB2011UiAS-2HnD;
- winbox - moved "Too Long" statistics counter to Ethernet "Rx Stats" tab;
- winbox - show "System/RouterBOARD/Mode Button" on devices that have such feature;
- wireless - fixed antenna gain setting on RBSXT5nDr2;
- wireless - improved antenna gain setting for devices with built in antennas;
- wireless - improved AR5212 response to incoming ACK frames;
- wireless - improved connection stability for new model Apple devices;

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn't either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn't be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don't always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you're looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don't power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don't miss the update that will improve your device.