Versions:
- Firmware - 4.230.30-3586
- BIOS - 6.17.04.0
- UEFI_Driver - 0x06060A01 (Signed)
- Hii - 03.07.12.01 (Signed)
- FCODE - 4.16.08.00
- NVDATA - 3.1403.00-0085
- BootBlock - 3.02.00.00-0001
- Ctrl-R - 5.04-0002
- PCLI - 1.07.05
- ROMENV - 1.09
This download is valid for the product(s) listed below
- Intel RAID Controller RS3DC040
- Intel RAID Controller RS3DC080
- Intel RAID Controller RS3MC044
- Intel RAID Controller RS3SC008
Fixes:
- When we attempt to retrieve iMR Thunderbolt controller firmware logs using an application, we see some lines that are wrapped without starting on a new line.
- Serial prints getting jumbled up due to print message inside spurious interrupt handler.
- Data Corruption is taking place on Windows OS installed on top of ESX 5.5 U1 OS.
- ONFI: To properly handle the OCR case with RESET Status Register.
- Cache offload failure with pinned cache on R5 VD
- Defect Fix for VPD and inquiry callback issues in DISM
- Patrol read will not start on any VD after a PR is started, suspended and VD is deleted
- Defect Fix for Command gets retried infinitely times when drive responds with 0B/47/03 always
- FW failure during read on 3PD R5 with 1000 CME with skip count 2
- FW breaks if wrong security key is entered
- Only 1mb crash dump is getting generated of fw fault
- not enough bs found during double Dip power cycle Test
- cache restore failure message displayed through cache restore was successful
- Routines to inject bit error in NF and ecc error in DDR for ONFI
- Mismatch in LD id and target ID during set/reset boot device
- on breaking the multipath in loop while drives are spinning up will result in montask
- FW hangs while creating 64 VDs on the controller with SLES11 SP2
- While running reconstruction from R1 to 4 drive PRL11 with IO,FW hits to MonTask: line 1270 in file ../../raid/1078dm
- SMART poll needs to issue log sense with page control set to current/ cummulative value
- static analysis tool defects resolution
- added support for debug queue
- Not getting "Clear ldbbm badblocks" options on VD
- FW goes to kill adaptor to handle partial copy of crash_dump
- Montask in divert.c seen when injecting 64K consecutive errors on R0 VD, Patrol Read running in background.
- PR Progress event is not generated for 1TB/3TB SATA drive
- Defect fix for kernel panic with iMR Fury with FreeBSD driver
- Running Storcli /C0/CV show or (show all) starts a relearn on supercap issue
- Defect Fix for Online DIF drives are getting punctured after PI enabled R5 VDs are offlined with pinned cache
- md5sum mismatch seen on a copied file from R5 VD with CME
- Power removal of enclosure FW hits to MonTask: line 4056 in file ../../bbu/onfiBBM.c
- Fix GNU make file compilation
- Crash Dump Error Handling
- When OS on VD ,after collecting crash dump file system becomes readable
- Physical drives go to power save mode just after restarting the server
- storcli and CtrlR still show new PD information as 4K sector after replacing a 4K sector drive with a 512 sector drive
- Unexpected power state change
- Media error on Last sector of stripe isn't added to LDBBM list
- CME logic using overlaid fields in c->rec
- defect fix for Compilation issue
- Too many unexpected sense AEN raised by CC during CME recovery on R5
- Not able import foreign configuration immediately after breaking the mirror.
- FW should not try to boot iMR mode without informing host if ECC error happens when OS is running.
- spin up tracker dequeue is not handled for case in which TUR error happens even after MAX retries
- Kill adapter is seen while performing CME recovery during Write operation.
- PDs more than 32 which has configuration, is reporting as JBODs after importing from MR to IMR
- hostCmdSortingWrites is not updated when VD policy changes(WT/WB)
- The restore successful and unsuccessful prints to be handled properly
- code review change implemented
- Changes to support PD IO history
- Enable break mirror support
- Implemented Fix to Problem [PDs more than 32 which has configuration, is reporting as JBODs after importing from MR to IMR]
- Moved divert code from iopath region to save memory
- Update Ptolemy VPD and GasGauge with COL settings for a OEM
- Disable sgpioSmpPresenceDetect for OEM
- Show valid ROC temperature
- Change SES Green/Amber LED behavior
- Extended LDBBM table to hold more bad block entries; with relevant increase in divert nodes.
- Adding test routine for the bad block loop test
- Modify MR fw to eliminate four second window where drive swap is not recognized.
- Single image support for ONFI
- Implement CME solution for "Do not allow 3 minute timer to expire forcing driver to kill fw on CME/disk timeout/etc.
- Make MR to iMR migration generic on TMM fault
- Support for DIS feature in dual image
- command storclif /c1 start diag duration=0 causes controller card to montask.
- BGI operation still running on RAID0 VD even after PI protection disabled
- LED Blink operation doesn't stop after VD deletion
- SGPIO functionality is not working when only cable A is connected
- Potential null pointer dereference
- cache restore failure message displayed through cache restore was successful
- RAID configured on PD been erased with Normal or Thorough will lost after system reboot/reset
- CME handling of Invader
- Cache policy of Virtual Drives(VD) does not change to Write Through(WT) mode even after detecting a bad supercap.
- SSD causes system to hang at POST
- Behavior change when FW hit fault code 0x81 (uncorrectable ECC error)
- Adding 2GB DDR and 4GB Flash combination support for Single Image Write.
- FW hits MonTask: line 1143 in file ../../raid/pd.c on starting VD erase in standard mode.
- FW crash while launching Ctrl+R
- 9240-4i is not getting required memory resources on boot, on Linux it waits 5 minutes, resets the
- L2/L3 cache error on H330 MM & H330 MB on reboot
- Work Around for PPC476 Errata number 46 in MR Firmware
- Work Around for PPC476 Errata number 46 in iMR Firmware
- disableBatteryWarning should not be reset if changed by user
- firmware 25.2.0-0013 causes the SEP to not be seen on x4 Equinox
- Transparent Learn Cycle does not kick off and RSOC (Relative State Of Charge) eventually goes down to 0%.
- EEprom CRC error is detected when WebBIOS is running
- AdpDiags does not fail when the SAS link is down
- HDD resume failed during dimmer switch test method.
- Add MaintainPdFailHistory clear function
- Updated long term WA for PPC errata number 46
- For a particular OEM, size of some 4TB drives is reported as zero
- Rebuild failed event is not seen when rebuild fails due to LDBBM and SBBM tables getting full (puncturing disabled)
- Implement I2C Slave Address for Sideband Management
- OEM hi-temp warning not being displayed
- OEM SGPIO support not working
- Retention test failure during stress test
- cntr-R fails to show correct PD sector size once PD's swapped to same slot 512B PD with 512e PD type
- Assertion failure (not enough BS found) in double DIP power cycle test case
- DIS mismatch while running system reboot script with dirty data in DDR
- FW goes to montask at cache offload.
- Megamon during Injecting errors to VD with 512e PDs on iMR controller
- Faulty protocol used for changing the Disk Write Cache Policy
- "OOB:Got DCMD, but FW is not ready " messages are flooding in tty log during OCR .
- Prevent overtemp warnings while charging between 45C and 50C
- adapterOperations.alarmControl is being set to 1 even if controller does not have alarm on board
- CLI Reporting of TMM VPD
- megacli reports battery pack is missing on hot insertion
- MonTask: line 4699 in file ../../raid/ld.c seen on iMR FW during boot to OS with R0 and PRL11 VD
- Do not print VPD86 errors for BP/expander
- Modify WCE bit for improved Linux performance
- When attempting to secure LD during RLM, receive option to secure LD, LD not secured (message incorrect/misleading.)
- Megamon issue when disabling the drive security on a MR controller with spun down FDE drives.
- Unable to open "Set Patrol Read Properties" in MSM with 2008-iMR
- Initialize deviceExposure with MAX_INT13DISKS instead of 0xFF
- Make sure all the make file adheres to the latest binary names.
- Provide an option to limit the max number of INT 13h devices presented to system BIOS
- StartHiiBackEnd() has Print statement with %g
- UEFI Driver should calculate checksum before setting bios data (MR_BIOS_DATA)
- System hang when we press F1 on second time when we are in HII form
- UEFI Driver- has debug print statements during POST
- Diskpart EFI utility can't create partition on a JBOD
- Support EFI_FIRMWARE_MANAGEMENT_PROTOCOL for controller firmware upgrade.
- UEFI Driver returns EFI_NOT_FOUND when platform passes valid Target for ExtSPT.BuildDevicePath()
- Install FMP on Controller Handle at Start() and the exception
- FMP GetImageInfo could result in stack corruption - Code Review Defect ID D26304
- User can't access RAID HII in UEFI mode after removing a HDD
- HII\EKM-LKM without reboot should show proper message
- Without selecting any drives I am seeing the previous config VD size.
- Configuration Restore is not working
- StartHiiImpl() WriteToLogger uses %g and EFIHiiDriverEntryPoint() Print statement uses %g for displaying EFI status
- Getting error message when we suspend Patrol read operation through HII browser
- Remove duplicated strings from the UNI FIle
- Allow user to select RAID level when controller has other VD + error handling
- fixing code review defects (AIM version + UCM GUID + deallocation)
- Firmware updation fails in OEM machine
- Form UF003 prints error messages (use WriteToLogger to log these debug messages)
- FWMgmt Prtocol:<config ID="LSIMegaRAIDConfigurationTool"> has no "versionid" info.
- Help content for Firmware Update in Controller Management is inappropriate
- Enter security key for locked drives screen, press down to get to OK, OK will show up again on right
- VD details display is improper in Expand Virtual Drive
- Advanced Controller Properties- Power Saving Settings has broken form
- Able to select EKM even when the EKM FOD key is removed from the system.
- System/HII hang when clicks on Hardware Components menu option in HII.
- On Success of creating Drive Security Form loads into Advanced controller properties
- IMR Liberator Drop Down option in VD properties for Cached is present
- Customize help string for Select Interface Type
- Fill Controller Index in RouteConfig + for UF003 calculate checksum only for the actual config size
- Auto Learn Mode is showing wrong data
- Addressed review comments
- Typo in HII form Controller Status
- Toggling between Legacy to Uefi mode vice versa junk values seen .
- HII PKG 0006/Going from LKM to EKM asks for a Current Security key Identifier and Security key.
- On selecting a wrong parameter for size while creating VDs, Options greyed, Create VD page exits to parent page.
- Security feature is enabled but HII sees "Drive Security" as disabled
- UCM Phase 1: Typo "Clear Configuration" -> "Clear Configuration"
- Handling Code Collaborator Review Defects
- added a while loop and take care of the multiple PD Groups scenario.
- HII should calculate checksum before setting bios data (MR_BIOS_DATA)
- MR6.3 HII aesthetic change
- Changing Percentage of Space to Expand Does not Update Final VD Size
- AIM (Agentless Inventory Manager) Issues
- Creation+ FW updation+ Scan foreign Configuration is disabled/grayed out in HII page
- HII 03.07.05.00/Under advanced controller properties and selecting Cache and Memory, it says's "scontroller cache"
- To address FW Update help Strings
- Not able to schedule CC in concurrent mode from HII(03.07.09.00).
- HII. Provide controller FW update function
- HEFU. Simplify controller property page
- Remove limitation for creating R6 in HII for OEM
- Provide pop-up to display current version and update fw version as part of HEFU HII Firmware Update functionality
- (Implemented) - Create a formset with classGUID that customer has provided.
- Move Disable Protection option from Controller Management to VD management
- System hang observed when the "PdInfo.userDataBlockSize" is set to 0
- HII help for Boot error handling does not display "Stop On Error" option
- Remove FMP installed on the controller handle in HII
- RSOD during POST after enabling SecureBoot - HEFU.ROM should report exact size of .EFI image
- UCM Phase 1: Allow user to select RAID level when controller has other VD + error handling
- Consistency Check Start - remove mm/dd/yyyy from the string as the format is out of control of LSI
- Missing BBU caused disappearance of Enclosure Mgmt opt in BIOS setup
- HII help window shows unsupported stripe sizes
- In HII on a ready drive we are able to see Used space as 40Gb.
- Enhance help message for PD/VD Operation field
- PCLI(1.07.05) Sparc: Command "cli set securitykey=Lsi@12345" fails with errcd "1001" and errmsg "invalid key".
- Revise Drive Spin-Up Timing on OEM 12G iMR and MR Boards
- Addition of ManPage1 values to the xml file.
- Customer NVDATA Change request for iMR
- Dual write NVDATA changes for customer
- Flatwoods Showing Same Slot Number for All Drives
- breakMirrorRAIDSupport for single span Raid 1
- Memory/battery problems in Focused Regression
- Coherency bit is disabled in SRAM TLBs
- Added a new Control to enable/disable JBOD on the controller in Ctrl Mgmt page.
- Display the Battery status as N/A for iMR cards.
- current write policy is not getting updated until we press f5
- unable to display the reason for difference in write policy
- Both the Connector information(0-3 & 4-7) is not shown in PD properties while connected in Multipath
- Write policy is not added with writeback with BBu when MFC is set
- VD Erase will be disabled in Ctrl+R when Initialization on particular VD is aborted
- Added the code to unset the boot-device to NONE
- StorCLI - MR 6.2 StorCLI help syntax is wrong for R1EC
- PCLI Sparc(1.07.02):" Cli show all" command fails with error msg "Error! App exec failed in FW PCLIError! Internal".
- CATEGORY:
- Motherboard
- COMPATIBLE WITH:
- OS Independent
- file size:
- 34.7 MB
- filename:
- 3108-MR_FWPKG_v24.3.0-0054.zip