Intel ir3 2208 ROC Hardware RAID Firmware 23.28.0-0010

Firmware- 3.400.05-3175

- External Key management security for iMR
- Not seeing the correct Boot Message when the connection to the External Key Management server is down
- Re-keying a controller with External Key Management(EKM) security enabled, results in a corrupted key ID.
- Performing an online firmware update or Online Controller Reset(OCR) on a controller with External Key Management(EKM) enabled, results in all secured drives marked as foreign.
- Raid configuration loss after reboot- PDs in POWERSAVE
- Re-keying in External Key Management mode followed by disabling security and enabling LKM results in a bail out while creating a Virtual Drive
- FW debugger scrolls continuous message and eventually resets after deleting Source VD during a Cachecade disassocation
- Switching to Local Key Management Mode(LKM) after a rekey in External Key Management(EKM) rekey without rebooting results in HII saying key incorrect but Firmware says key was created.
- On a controller with Local Key Management(LKM) enabled, user is asked to enter the security key to unlock and import a foreign, locked and External Key Management(EKM) enabled drive.
- After starting Patrol Read in the HII application, booting to OS and checking the status in MSM shows Patrol Read as suspended.
- Getting Question Value mismatch when entering Controller management screen
- MR to iMR downgrade error
- Pinned cache gets flushed to incorrect VD for mirrored RAID levels
- Cache policy of Virtual Drives(VD) does not change to Write Through(WT) mode even after detecting a bad supercap.
- Cannot create pinned cache during an Online Controller Reset (OCR)
- Switching the security mode from External Key Management(EKM) to Local Key Management(LKM) on iMR controller will result in a corrupted controller key.
- Getting a non informative message when trying to import a Virtual Drive after a re-key without reboot
- Internal Development team defect to check-in gemini image to resolve SSD drives missing issue.
- Unable to suspend the Patrol Read operation in iMR mode from the HII application
- Bad battery warning message that comes up during POST isn't aligned properly.
- HDD status LED will be lit red after creating and deleting LD but the status is normal via MSM
- Firmware break into montask, when there is a pinned cache( During bootup and OCR )
- Controller breaks into montask if you have 10 enclosures connected to the controller.
- VD erase does not resume and complete after reboot.
- A data TLB error occurs when the External Key Management Server(EKMS) is down and drive security is changed from External Key Management(EKM) mode to Local Key Management(LKM) mode.
- Remove redundant code within a particular function
- Storecli reporting incorrect values for tfm and supercap date of manufacture
- Static analysis tool defects
- Unable to discard pinned cache in Headless Safe Mode.
- Enhance code to catch Stack Overflow problem as soon as it occurs.
- Write buffer flash programming support
- Implement I2C Slave Address for Sideband Management
- Add Fastpath Support by Default for a particular OEM.
- When pinned cache present VD property not changing from WB to WT.
- PDs go online without VD created & App doesn't allow any VD creation on passing a wrong parameter in Spanned VD.
- Booting a 12G server into a degraded Raid 5 array will result in limited functionality
- Improve Boot time that was lengthened due to previous change.
- (DDR3) CKE and Reset clamping circuit can cause DDR errors at initialization time
- Incorrect variable type in MR Read/Modify/Write path
- Gemini image updated
- Raid configuration loss after reboot- PDs in POWERSAVE
- RAID configured on PD been erased with Normal or Thorough will lost after system reboot/reset
- OEM MR TB controller reports foreign configuration on adapter during a 100 AC power cycles
- Cache policy of Virtual Drives(VD) does not change to Write Through(WT) mode even after detecting a bad supercap.
- FW sending wrong configuration data during boot msg pending state
- I/O's fail and VD becomes failed during planned failover of owner node w/ SMB I/O
- Configuration import of GHS (Global Host spare) fails.
- Firmware hits Montask when drive is pulled after changing the volume property from read ahead to no read .
- VPD output of lspci –vvxxx showing [RV] Reserved: checksum bad, 86 byte(s) reserved
- Gemini image updated
- disableBatteryWarning should not be reset if changed by user
- An invalid frame sent during a PIO-mode SATA passthrough command results in resetting the drive
- Fix for Infinite retries of command for sense code 0B/47/03
- Liberator Card loses its boot VD after many reboots
- Upgrading from Software RAID to 9260-8i causes Alarm to sound
- Incorrect variable type in MR Read/Modify/Write path
- Bad or Missing TMM boot message is changed to Critical error
- In case of a certain OEM iMR shows R5 enabled.
- Running out of free entries in task list due to recursive addition of tasks
- Fix for Infinite retries of command for sense code 0B/47/03
- RAID configured on PD been erased with Normal or Thorough will lost after system reboot/reset
- Kill adapter is seen while performing CME recovery during Write operation.
- CME logic using overlaid fields in c->rec
- system black screen during S1 Sleep test
- Operating System event log reports a controller error during stress testing
- With Headless Continue On Error Mode(HCOE) enabled and the SafeStore BIOS password enabled, if the wrong password is entered you are stuck at the same screen .
- An invalid frame sent during a PIO-mode SATA passthrough command results in resetting the drive
- Liberator Card loses its boot VD after many reboots
- Code Review: Call DDF_discardInvalidPds only if DS3 is enabled
- FW take a long time to boot to OS
- Cluster validation failed in disk arbitration
- HDD status LED will be lit red after creating and deleting LD but the status is normal via MSM
- Deep learn will not start immediately when Relative State of Charge (RSOC) of battery is equal to 95%.
- Patrolread will not start on any VD after a PR is started, suspended and VD is deleted
- VD goes offline when we start reconstruction on 32 Drive R0 VD
- Clear up stale cache lines.
- OEM MR TB controller reports foreign configuration on adapter during a 100 AC power cycles
- MR 6.3: md5sum mismatch seen on a copied file from R5 VD with CME
- Deep learn will not start immediately when Relative State of Charge (RSOC) of battery is equal to 95%.
- search for one wire devices prints are masked after the boot

BIOS- 5.46.02.0

- Initialize deviceExposure with MAX_INT13DISKS instead of 0xFF
- Make sure all the make file adheres to the latest binary names.
- Provide an option to limit the max number of INT 13h devices presented to system BIOS

Hii- 03.07.11.00

- HII\EKM-LKM without reboot should show proper message
- With out selecting any drives I am seeing the previous config VD size.
- Confiuration Restore is not working
- StartHiiImpl() WriteToLogger uses %g and EFIHiiDriverEntryPoint() Print statement uses %g for displaying EFI status
- Getting error message when we suspend Patrol read operation through HII browser
- Remove duplicated strings from the UNI FIle
- Allow user to select RAID level when controller has other VD + error handling
- fixing code review defects (AIM version + UCM GUID + deallocation)
- Firmware updation fails
- Form UF003 prints error messages (use WriteToLogger to log these debug messages)
- FWMgmt Prtocol:<config ID="LSIMegaRAIDConfigurationTool"> has no "versionid" info.
- Help content for Firmware Update in Controller Management is inappropriate
- Enter security key for locked drives screen, press down to get to OK, OK will show up again on right
- VD details display is improper in Expand Virtual Drive
- Advanced Controller Properties- Power Saving Settings has broken form
- Able to select EKM even when the EKM FOD key is removed from the system.
- System/HII hang when clicks on Hardware Components menu option in HII.
- On Success of creating Drive Security Form loads into Advanced controller properties
- Drop Down option in VD properties for Cached is present
- Customize help string for Select Interface Type
- ill Controller Index in RouteConfig + for UF003 calculate checksume only for the actual config size
- Auto Learn Mode is showing wrong data
- Addressed review comments
- Typo in HII form Controller Status
- Toggling bewtween Legacy to Uefi mode vice versa junk values seen .
- HII PKG 0006/Going from LKM to EKM asks for a Current Security key Identifier and Security key.
- n selecting a wrong parameter for size while creating VDs, Options greyed, Create VD page exits to parent page.
- Security feature is enabled but HII sees "Drive Security" as disabled
- Typo "Clear Configuaration"-> "Clear Configuration"
- added a while loop and take care of the multiple PD Groups scenario.
- HII should calculate checksum before setting bios data
- MR6.3 HII aesthetic change
- Changing Percentage of Space to Expand Does not Update Final VD Size
- AIM (Agentless Inventory Manager) Issues
- Creation+ FW updation+ Scan foreign Configuration is disabled/grayed out in HII page
- Under advanced controller properties and selecting Cache and Memory, it says's "scontroller cache"
- To address FW Update help Strings
- Not able to schedule CC in concurrent mode from HII(03.07.09.00).
- HII. Provide controller FW update function
- HEFU. Simplify controller propety page
- Remove limitation for creating R6 in HII
- Provide pop-up to display current version and update fw version as part of HEFU HII Firmware Update functionality
- Create a formset with classGUID that customer has provided.
- Move Disable Protection option from Controller Management to VD management
- Able to select EKM even when the EKM FOD key is removed from the system.
- System hang observed when the "PdInfo.userDataBlockSize" is set to 0
- HII help for Boot error handling does not display "Stop On Error" option
- HII PKG 0006/Going from LKM to EKM asks for a Current Security key Identifier and Security key.
- Enter security key for locked drives screen, press down to get to OK, OK will show up again on right
- HII\EKM-LKM without reboot should show proper message
- UCM Phase 1: Allow user to select RAID level when controller has other VD + error handling
- System hang observed when the "PdInfo.userDataBlockSize" is set to 0
- HII help window shows unsupported stripe sizes
- Missing BBU caused disappearance of Enclosure Mgmt opt in BIOS setup
- In HII on a ready drive we are able to see Used space as 40Gb.
- Typo "Clear Configuaration"-> "Clear Configuration"
- added a while loop and take care of the multiple PD Groups scenario.

FCODE- 4.16.08.00

UEFI_Driver- 0x06060900
- UEFI Driver: StartHiiBackEnd() has Print statement with %g
- UEFI Driver should calculate checksum before setting bios data
- System hang when we press F1 on second time when we are in HII form
- UEFI Driver- has debug print statements during POST
- Diskpart EFI utility can't create partition on a JBOD
- Support EFI_FIRMWARE_MANAGEMENT_PROTOCOL for controller firmware
- UEFI Driver should calculate checksum before setting bios data
- UEFI Driver returns EFI_NOT_FOUND when platform passes valid
- User can't access RAID HII in UEFI mode after removing a HDD

WebBIOS- 6.1-71-e_71-Rel

NVDATA- 2.1403.03-0128
- Added support for subOEM 8 version of Alcor-S 9271 Controller

PCLI- 05.07.00

BootBlock- 2.05.00.00-0010

BootBlockCommon- 07.26.26.219

ROMENV- 1.08

This download is valid for the products listed below:

- Intel Integrated RAID Module RMS25CB040
- Intel Integrated RAID Module RMS25CB080
- Intel Integrated RAID Module RMS25PB040
- Intel Integrated RAID Module RMS25PB080
- Intel Integrated RAID Module RMT3CB080
- Intel Integrated RAID Module RMT3PB080
- Intel RAID Controller RS25AB080
- Intel RAID Controller RS25DB080
- Intel RAID Controller RS25NB008
- Intel RAID Controller RS25SB008