Intel iMR 3008 ROC Hardware RAID Firmware 24.9.0-0024

Versions:

- Firmware 4.290.00-4591
- ROMENV 1.09
- BootBlock 3.07.00.00-0002
- NVDATA 3.1507.00-0009
- UEFI_Driver 0x060E0300 (SIGNED)
- Hii v03.14.09.00 (SIGNED)
- FCODE 4.17.08.00
- BIOS 6.25.03.0
- Ctrl-R 5.10-0700
- PCLI 1.07.05

Changes:

- Numerous changes for specific customers
- (Closed) - MSM displays error message if 'Schedule Consistency Check' is selected.
- (Closed) - Invader firmware (4.280.00-4331 in MR 6.7) with write-verify has abnormal behavior/performance.
- (Closed) - Blade DMA errors observed while running IOs
- (Closed) - MR6.6 Controller is not accessible through OOB before OS is up and running
- (Closed) - Exception seen during OS Reboot heat run test
- (Closed) - Unable to update drive firmware on customer specific FDE SATA SSDs
- (Closed) - Few test cases fail when PCIe tool is executed
- (Closed) - Creation and productization of new product SKU for 9361-8i board with 2GB of memory
- (Closed) - Re-branding effort for customer.
- (Closed) - Fault LED support for predictive failure drives for SGPIO
- (Closed) - Integrate 08.00.05.00 MR PL with MR 6.8
- (Closed) - GPIO Settings for a customer
- (Closed) - OEM wants controller VPD reporting should be disabled
- (Port_Complete) - Unable to Convert a JBOD PD to UG in Solaris
- (Port_Complete) - Instruction TLB error seen when auto configuration command executed from CLI application
- (Port_Complete) - Performing a cable pull/push with array property change resulting into FW hang.
- (Port_Complete) - Exception in core 0 is seen when drives are spun down and an ocr is triggered
- (Port_Complete) - Commands to the fde drives are not responding within 500ms.
- (Port_Complete) - Enable I2C clock frequency of 100kHz for specific OEM is not working accurately
- (Port_Complete) - Handle enabling disk "write" cache setting from OS for OEM
- (Port_Complete) - Firmware halted and restarted while doing flash erase on the onfi flash
- (Port_Complete) - Secure Erase on SATA SSD via CtrR or HII leads to unresponsive application, Secure erase failing intermittently
- (Port_Complete) - chain element for non RW commands were not pulled in the FW
- (Port_Complete) - Rebuild Performance for RAID 1 arrays is slower.
- (Port_Complete) - MSM displays error message if 'Schedule Consistency Check' is selected.
- (Port_Complete) - Patrol Read Properties window does not pop up on MSM
- (Port_Complete) - Continuous "TASK_ABORT_INTERNAL" prints observed in FW, after running heavy IO's on JBOD configured using 12Gig SAS SSD
- (Port_Complete) - L2 unrecoverable cache error was seen during Patrol read properties modification in certain conditions.
- (Port_Complete) - Controller cache fails to destage when multiple SVDs are present
- (Port_Complete) - Vd erase does not resume after reboot in the presence of CCVD
- (Port_Complete) - Controller boots to OS Even when Pinned Cache is present and Boot Error handling is set to Stop on Error.
- (Port_Complete) - Fw hits to MonTask: line 1272 in file ../../raid/1078dma.c while running IO in VM
- (Port_Complete) - Unexpected controller reset during test run
- (Port_Complete) - Failed to import iMR RAID configuration to 12G MR
- (Port_Not_Required) - L2 unrecoverable cache error was seen during Patrol read properties modification in certain conditions.
- (Port_Complete) - Controller Reboots after doing an OCR with IOs running in the background
- (Port_Complete) - Fault LED support for predictive failure drives for SGPIO
- (Port_Not_Required) - flush cache with write_verify on R0 volume and sata drive
- (Port_Complete) - MR & iMR FW Work-around is required for 3x08 chip Errata ID - 2012-RC714 for PCIE 3.0 compliance
- (Port_Complete) - FW unable to detect the inserted drives
- (Port_Complete) - Disable FLR support in MR FW to address VMware guest VM abrupt shutdown issue
- (Port_Complete) - Windows BSOD when upgrade FW 24.6.0-0040 to 24.8.0-0026 with driver 6.707.08.00
- (Port_Complete) - Need to set perfTunerMode appropriately on controller reset.

This download is valid for the products listed below:

- Intel Integrated RAID Module RMS3HC080
- Intel RAID Controller RS3WC080

About SATA / AHCI / RAID Controllers:

When enabled by appropriate software, the SATA controller (RAID or AHCI) is properly recognized by the system and all of its features are made accessible.

In addition to that, the computer will have the ability to read all adapter characteristics, such as model and manufacturer, and will also be able to manage physical disk drives through the controller’s interface.

If you wish to apply this package, all you have to do is to make sure that the current release is compatible with both your adapter model and your operating system, and then to get the downloadable software. Extract it if necessary, run the available setup, and follow the on-screen instructions for a complete installation.

When finished, remember to perform a system reboot to make sure that all changes take effect properly. Please remember that, even though other OSes might also be compatible, we do not recommend installing this software on platforms other than the specified ones.

That being said, click the download button, get the package and apply it on your computer. Moreover, constantly check with our website to stay up to date with latest releases.