Intel MR 3108 ROC Hardware RAID Firmware 24.21.0-0067

Firmware Package:24.21.0-0067 (MR 6.14 Point Release 2)

- Firmware 4.680.00-8392
- ROMENV 1.09
- BootBlock 3.07.00.00-0003
- NVDATA 3.1705.00-0016
- UEFI_Driver 0x06180203 (SIGNED)
- Hii 03.25.05.10 (SIGNED)
- FCODE 4.19.08.00
- BIOS 6.36.00.3
- Ctrl-H 5.19-0603
- PCLI 1.07.05

Bug Fixes and Enhancements:

- FW returns success for enabling encryption when it is failed on the drives
- Fix for proper LED blink update call for drives behind expander
- Firmware hits MonTask when it tries to PIN the cacheline in flush context during cable pull
- 9460-8i is reporting Chip Temperature of 255 when the ambient temp is about 0 C
- Ctrl-R hang after certain multiple create/remove VD operations and/or clear configurations
- Proper Error message not displayed after clean flash of boot block only after reboot

UEFI (EFI 2.0) instructions for updating RAID Firmware:

1. Download and extract all files to a local drive.
2. Boot the target system to EFI shell.
3. Change directory to the local drive and directory containing the flash update files and the firmware image file.
4. Type "update.nsh" or "eficmdtool2 -adpfwflash -f MR514p3.rom -noverchk -aall"
5. Wait for the flash to complete. Do NOT reboot the system during the update.

Windows and Linux instructions for updating RAID Firmware:

- The firmware update may be run from Within Windows or Linux using the appropriate versions of CmdTool2.
-In Windows, unzip the utility into the same directory as the rom file by typing "cmdtool2 -adpfwflash -f MR514p3.rom -aall".
-The Linux CmdTool2 by running the rpm and then calling the utility from /opt/MegaRAID/CmdTool2 as "./CmdTool2 -AdpFwFlash -f MR514p3.rom -aall"

DOS instructions for updating RAID Firmware:

1. Download and extract all files to a local drive.
2. Boot the target system to DOS.
3. Change directory to the local drive and directory containing the flash update files and the firmware image file.
4. Type "update.bat" or "doscmdtool2 -adpfwflash -f MR514p3.rom -aall"
5. Wait for the flash to complete. Do NOT reboot the system during the update.

This download is valid for the products listed below:

- Intel Integrated RAID Module RMS3CC040
- Intel Integrated RAID Module RMS3CC080
- Intel RAID Controller RS3DC040
- Intel RAID Controller RS3DC080
- Intel RAID Controller RS3MC044
- Intel RAID Controller RS3SC008

About SATA / AHCI / RAID Drivers:

When you install an operating system, SATA settings (be it AHCI, RAID, or IDE mode) are detected from the BIOS. If you want to change from one mode to another after the OS has been applied, appropriate drivers are required.

Bear in mind that if you modify these settings without installing proper files first, the operating system will not be able to boot until changes are reverted or required drivers are applied.

To perform the latter task, get the package, run the available setup and follow the instructions displayed on-screen for a complete installation. Afterwards, perform a system reboot so that all changes take effect, enter BIOS menu, and set the SATA option to the mode that best describes the newly applied drivers.

So, if you intend to modify the SATA settings to the mode described by this release, click the download button, and make the desired changes. In addition to that, don't forget to constantly check with our website so that you don't miss a single new release.