ASUS P8H61 PRO ASMedia AHCI Driver 1.3.4.0 for Windows 8

CPU:

- Intel Socket 1155 for 2nd Generation Core i7/Core i5/Core i3 Processors
- Supports Intel 32 nm CPU
- Supports Intel Turbo Boost Technology 2.0

Chipset:

- Intel H61(B3)

Memory:

- 2 x DIMM, Max. 16GB, DDR3 1333/1066 MHz Non-ECC, Un-buffered Memory
- Dual Channel Memory Architecture
- Supports Intel Extreme Memory Profile (XMP)

Expansion Slots:

- 1 x PCIe 2.0 x16
- 2 x PCIe 2.0 x1
- 3 x PCI

Storage:

- Intel H61(B3) chipset : 4 x SATA 3Gb/s port(s), blue
- ASMedia ASM1061 controller : 2 x SATA 6Gb/s port(s), navy blue

LAN:

- Realtek, 1 x Gigabit LAN Controller(s)

Audio:

- Realtek ALC887 8-Channel High Definition Audio CODEC
- Supports : Jack-detection, Multi-streaming, Front Panel Jack-retasking
- Optical S/PDIF out port(s) at back panel

USB Ports:

- ASMedia ASM1042 controller : 2 x USB 3.0 port(s) (2 at back panel, blue)
- Intel H61(B3) chipset : 10 x USB 2.0 port(s) (6 at back panel, black, 4 at mid-board)

Back I/O Ports:

- 1 x PS/2 keyboard (purple)
- 1 x PS/2 mouse (green)
- 1 x LAN (RJ45) port(s)
- 2 x USB 3.0
- 6 x USB 2.0
- 1 x Optical S/PDIF out
- 6 x Audio jack(s)

Internal I/O Ports:

- 2 x USB 2.0 connector(s) support(s) additional 4 USB 2.0 port(s)
- 1 x COM port(s) connector(s)
- 2 x SATA 6Gb/s connector(s)
- 4 x SATA 3Gb/s connector(s)
- 1 x CPU Fan connector(s)
- 2 x Chassis Fan connector(s)
- 1 x S/PDIF out header(s)
- 1 x 24-pin EATX Power connector(s)
- 1 x 8-pin ATX 12V Power connector(s)
- 1 x Front panel audio connector(s) (AAFP)
- 1 x System panel(s)
- 1 x MemOK! button(s)
- 1 x Turbo Key II switch(es)

Form Factor:

- ATX Form Factor
- 12 inch x 8.4 inch ( 30.5 cm x 21.3 cm )

About SATA / AHCI / RAID Drivers:

When you install an operating system, SATA settings (be it AHCI, RAID, or IDE mode) are detected from the BIOS. If you want to change from one mode to another after the OS has been applied, appropriate drivers are required.

Bear in mind that if you modify these settings without installing proper files first, the operating system will not be able to boot until changes are reverted or required drivers are applied.

To perform the latter task, get the package, run the available setup and follow the instructions displayed on-screen for a complete installation. Afterwards, perform a system reboot so that all changes take effect, enter BIOS menu, and set the SATA option to the mode that best describes the newly applied drivers.

So, if you intend to modify the SATA settings to the mode described by this release, click the download button, and make the desired changes. In addition to that, don’t forget to constantly check with our website so that you don’t miss a single new release.