Buffalo TS5410DN NAS Firmware 4.60

Bug Fixes:

- [System] Modified to patch vulnerabilities (CVE-2015-8325, CVE-2016-1908, CVE2016-3115, CVE-2016-6210, CVE-2016-6515, CVE-2016-10009, CVE-2016-10011, CVE-2016-10012, CVE-2016-10708, CVE-2017-15906, CVE-2018-15473, CVE-2018-20685, CVE-2019-6109, and CVE-2019-6111).
- [Storage] Fixed a bug where the connection status for the internal drives could not be detected properly.
- [Storage] Fixed a bug where drives that make up a RAID array could not be checked at bootup properly.
- [Storage] Fixed a bug where a RAID array was corrupted when using USB drives for restoration and initialization if a RAID 10 array was created on the TeraStation.
- [Storage] Fixed a bug where nothing occurred after clicking ‘Redetect Drive’ on the USB drive list page.
- [File Sharing] Fixed a bug where the TeraStation freezes when accessing a shared folder.
- [Microsoft Azure Storage Sync] Fixed a bug where the “Files Deleted in Backup Source” option was unexpectedly changed to “Delete from container” while changing a job setting.
- [File Sharing] Fixed a bug where unnecessary logs were recorded.
- [Microsoft OneDrive Sync] Fixed a bug where files on OneDrive were not automatically deleted when the same files that were saved in a second level or deeper remote folder were deleted.
- [Microsoft OneDrive Sync] Fixed a bug where multibyte characters in an error log were not displayed properly.
- [Dropbox Sync] Fixed a bug where certain authentication codes could not be registered to the TeraStation.
- [Amazon S3] Fixed a bug where the status showed “Disconnected” even if the TeraStation was connected to Amazon S3.
- [Power Management] Fixed a bug where a fan error was detected when a UPS device was connected.
- [Settings] Improved security of Settings page.
- [Settings] Fixed a bug where a power user could not change the logged-in user’s password.
- [Settings] Fixed a bug where the user was booted from Settings on Safari if a display language was changed.
- [Logs] Fixed a bug where the log file size became too large after the TeraStation restarts if a shard folder was configured as the target folder to save file access logs.

Caution:

- Please consult your local technical support representative if you experience any problems caused by this firmware update.
- Do not turn the unit off until the update is finished. It will take several minutes. You will receive a message when the update is finished.
- USB drives are not mounted automatically after a firmware update. To mount them, unplug and then reconnect them.

How to Use the Updater:

1. Connect the TeraStation properly and configure the TeraStation and a computer to run the updater on the same network subnet. The subnet masks should be the same and the first three numbers of the IP addresses should be the same. The last number of the IP addresses should be different.
For example, if the IP address and subnet mask of the computer are
" 192.168.0.10 , 255.255.255.0 "
and the IP address and subnet mask of the TeraStation are
" 192.168.1.150 , 255.255.255.0 "
then the updater will _not_ work properly.
In this case, reconfigure the TeraStation's IP address and subnet mask to
" 192.168.0.150 , 255.255.255.0 ".
Then they will be on the same subnet and the updater will work properly.
2. Close all applications. Also, stop or exit any firewall software.
3. Extract the downloaded file and run "TSUpdater.exe". When a TeraStation is detected, an update window will open.
4. Select the TeraStation to update if multiple TeraStation are connected.
5. Click "Update" and enter the TeraStation's admin password.
6. Click "OK".
7. Transferring and updating the firmware will start. Wait until it finishes. The info LED will blink during the update.
8. When the update finishes, a message will be displayed.

About Network-Attached Storage Updates:

Upgrading the Network-Attached Storage (NAS) firmware can improve the system's overall performance, stability, and security by adding various fixes for related issues, enhancing existing features (or adding support for new ones), or updating different applications.

Due to the high number of NAS manufacturers, as well as network storage types, installing a new firmware might not be always as easy as it appears – and not too safe either. Failing to perform a software update can cause serious malfunctions to the network storage.

So, before you even consider applying this release, carefully read the installation guide and initiate the process only when you have understood and completely familiarized yourself with all the steps.

Moreover, it would be best if you take into account using a UPS unit (Uninterruptible Power Supply) to perform this task, because no power disruption should affect the upgrade.

With all these aspects in mind, after you have read the installation guide, click the download button to apply this firmware version to your NAS. Remember to check back with our website in order to stay up to speed with the latest releases.