Intel ir3 2208 ROC Hardware RAID Firmware 23.12.0-0013

Firmware - 3.240.25-2382

- Coverity issues fix
- Sequential Read performance is less on CacheCade associated LD's.
- Firmware returns invalid data in OOB packet
- Double media error getting corrected during check consistency
- [MR5.4] CacheCade: ECC/Medium/Unrecoverable read errors handling Enhancement
- Significant drop in Sequenial read performance with Read Ahead policy
- The reliability and error recovery of the SuperCap firmware was improved.
- Disk missing sporadically during reboot of Puma3
- Adjusted the USB phy boost value for the Mars controllers with SubDevice IDs between 3510 and 3515.
- NCQ support is disabled in FW
- Athena Rack BMC see clock stetching on I2C bus
- Timeout in CIMC when creating a hotspare
- CC2.1_RA_Support : Data Corruption upon creating WB CCVD during Cache Flush
- reading SATA IDENT information using STP_Passthru doesn't work with latest
- Firmware blocked firmware download to interposer
BIOS - 5.42.00
- Extremely long delay when the controller POST in Legacy mode
- BIOS build date field is empty and build date is displayed as BIOS build time in SLT.
- OpROM not getting relocated to runtime segment if the segment address is 0xC0000
- Handle BT750 when B0 and D1 controller is present in HAMR system
- HAMR: BIOS to have a logic to filter CCVD and report Remote VD count at OpROM POST time
- FW Version number Truncated by one digit in OpROM POST screen
- BIOS: Provide scratch segment and populate info to assist Ctrl R to load latest host
- Update PERC9 Sub System Device Ids and the corresponding BBS strings.
- Retry read capacity if scsi status is not success
- MR HWR OpROM BIOS : OOB (BMC) function corrupts EBDA area used by other server function
Hii - 03.02.02.00
- HII hangs when trying to enter Configuration Management while in Safe Mode
- HII message for Safe Mode is not clear
- HEFU: Controller Status should reflect safe mode + don’t log debug messages in serial port
UEFI_Driver - 0x05270000
WebBIOS - 6.1-62-e_62-Rel
- Wrong spanned drive group size is displayed by Web bios(Ctrl-H)
PCLI - 05.07.00
FCODE - 4.12.05.00
NVDATA - MR2.1304.03-0118
- Added a subOEM 8 version of the AlcorTU 9273 controller and a subOEM 3 version of the Procyon 9290 controller
- Degraded performance comparison With the latest MR 5.3 -MR_3.190.25.1887 between Phase -3 Gemini Vs Phase -1 Gemini
BootBlock - 2.05.00.00-0010
Ctrl-R - 4.02-0001
BootBlockCommon - 07.26.13.219
ROMENV - 1.08

This firmware is valid for the products listed below:

- Intel Integrated RAID Module RMS25CB040
- Intel Integrated RAID Module RMS25CB080
- Intel Integrated RAID Module RMS25PB040
- Intel Integrated RAID Module RMS25PB080
- Intel Integrated RAID Module RMT3CB080
- Intel Integrated RAID Module RMT3PB080
- Intel RAID Controller RS25AB080
- Intel RAID Controller RS25DB080
- Intel RAID Controller RS25NB008
- Intel RAID Controller RS25SB008

About SATA / AHCI / RAID Drivers:

When you install an operating system, SATA settings (be it AHCI, RAID, or IDE mode) are detected from the BIOS. If you want to change from one mode to another after the OS has been applied, appropriate drivers are required.

Bear in mind that if you modify these settings without installing proper files first, the operating system will not be able to boot until changes are reverted or required drivers are applied.

To perform the latter task, get the package, run the available setup and follow the instructions displayed on-screen for a complete installation. Afterwards, perform a system reboot so that all changes take effect, enter BIOS menu, and set the SATA option to the mode that best describes the newly applied drivers.

So, if you intend to modify the SATA settings to the mode described by this release, click the download button, and make the desired changes. In addition to that, don't forget to constantly check with our website so that you don't miss a single new release.