Intel RMSP3AD160F RAID Module Trimode RAID Firmware 51.14.0-3514

Versions:

- Firmware Package: 51.14.0-3514 (MR 7.14 Point)
- Firmware 5.140.00-3247
- MR PL 14.25.07.00
- BootBlock 7.02.00.00-0021
- NVDATA (5.1400.00-0005)
- UEFI_Driver v0x070E0202 (Signed X64)
- Hii v07.14.06.02 (SIGNED)
- BIOS 7.14.00.0
- SBR: 5.1400.00-0465

FW Changes:

- DCSG00117832 - SPDMLIB: Add change to SConstruct to copy library output file ( .a) to release folder
- DCSG00216908 - NVRAM changes for supporting dynamic recon ghost tgtId
- DCSG00225192 - SPDM LIB: Set ECDSA signature with correct size in Signature field of SPDM Challenge response buffer before sending to BMC server
- DCSG00225977 - Implicitly error when converting an expression to a narrower type
- DCSG00231422 - PL NVMe : PCI task management is not getting completed.
- DCSG00297592 - Auto config RAID0 in HII did not work as expected
- DCSG00225219 - Unused phys are managed by VSes in SGPIO BP mode
- DCSG00237478 - [NVMe] SCSI log sense command timeouts seen while running 1MB IOs to NVMe drive
- DCSG00240573 - Use script to upgrade SAS SSD firmware will fail
- DCSG00240942 - In JBOD profile, set VD Write Cache to AWB shows success even though WB Supported is set to NO
- DCSG00242574 - NvmeAdmin: 'Exception handler called' observed while converting drive to Non RAID preceded by Export Log from OM
- DCSG00242613 - Correct Nvme Double Buffer module for multiple double buffer cases.
- DCSG00242940 - supportEPDWithAutoConfigOff supported bit is set as 1
- DCSG00243640 - Out of bound memory access when assigning dma group for controller devices.
- DCSG00244898 - controller FW printed ‘Assertion failure in fwcpuarmexceptions.c at line 1006: 0 during fio issue verify(2F) commands to sas hdd(JBOD) ’
- DCSG00246022 - CTRL_MFC_DEFAULTS_SET DCMD returning error when controller is in eHBA mode
- DCSG00249465 - Low risk temporary solution for preventing duplicate target Ids
- DCSG00255321 - User disabled PTB not reflected, hence PTB.txt is part of OnDemand SnapDump
- DCSG00255322 - PTB switch to Enabled and Save. No PoP up message reboot required/PTB.txt not part of Snapdump.
- DCSG00255323 - Controller Bios never sent the printing-has-completed DCMD
- DCSG00257908 - Last LDBBM entry in the list is not cleared after VD Deletion
- DCSG00258052 - Controller crash and resets on attempt to boot to windows OS
- DCSG00258546 - VSES: Incorrect linkup failed elements status reported on certain slots of the UBM backplane
- DCSG00263186 - UNMAP support is blocked and disabled
- DCSG00269097 - PRP-List overwritten in Double-Buffer-Copy-To-Host for response size > 8K
- DCSG00214352 - SMART Polling Improvement- API Changes
- DCSG00222915 - API change to add DCMD MR_DCMD_CTRL_LOCK_KEY_SECRET_KEY_APPLY and associated MFI STAT
- DCSG00223408 - Update mr_configpage.h file for New fields 'predFailPollDAInterval' and 'predFailPollInterval' in MPI2_MR_PARAMS_PAGE_0
- DCSG00225175 - SPDM_LIB: Support to build Challenge buffer with multiple GET_CERTIFICATE/CERTIFICATE_RESPONSE
- DCSG00226286 - Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - MR API
- DCSG00228248 - Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - nvram
- DCSG00229416 - New MFI Stat for the updated recon behavior
- DCSG00231443 - MR7 API: Add package incompatibility reporting
- DCSG00234391 - BST setup with Channel HBA + Elrond
- DCSG00237302 - Make necessary changes to atlas_bst in valscripts to enable BST
- DCSG00237413 - Persisting secureLD targetId bitmap
- DCSG00246317 - SMART Polling Improvement - API Changes
- DCSG00248087 - SMART Polling Improvement -New Dynamic Section to save New Controller properties structure in NVSRAM
- DCSG00256271 - To add return status MFI_STAT_OK_REBOOT_REQUIRED to MR_DCMD_LD_SET_PROPERTIES in mr.h
- DCSG00257777 - MFI SMP Port Num API changes
- DCSG00216966 - Execute once Auto configure option needs to be allowed for EPD-PT behaviour mode for certain controllers.
- DCSG00227036 - Preboot Trace Buffer [PTB] for Ventura/Aero - add a switch - MR firmware

MR PL:

- DCSG00212793 - BST: BST cancellations on cable breaker comm port unavailability
- DCSG00216461 - BST: UBM BST funtonality is broken on latest BST code.
- DCSG00228186 - Aero BST: Manage NVMe drive link up timing
- DCSG00231422 - PL NVMe : PCI task management is not getting completed.
- DCSG00239268 - BST: SAL reports unknown device type for drives
- DCSG00225219 - Unused phys are managed by VSes in SGPIO BP mode
- DCSG00237478 - [NVMe] SCSI log sense command timeouts seen while running 1MB IOs to NVMe drive
- DCSG00243640 - Out of bound memory access when assigning dma group for controller devices.
- DCSG00258546 - VSES: Incorrect linkup failed elements status reported on certain slots of the UBM backplane
- DCSG00023491 - Implemented secureSignCNG.exe CLI signing tool for Windows Signing.
- DCSG00030211 - Implement support for Cross certificate and command - Windows signing using CNG Provider with HSM Protected Key
- DCSG00040377 - Port secureSignBin.exe for MARGAY signing to GCP server environment
- DCSG00048670 - Aero multi-party signing partial signing of images
- DCSG00077215 - Signing Linux executables via GPG method in HSM
- DCSG00105430 - Implement changes to secureSign signing tool and infrastructure to support mixed list of PublicKeys that are from SCGCQ and DCSG.
- DCSG00129388 - Implemented change to use FTP instead of UNC for upload / download of unsigned / signed artifacts to workaround firewall issue.
- DCSG00143847 - Add support for signing MegaRAID Legacy BIOS CU Images (CTLR) images
- DCSG00234646 - Implement customSign.exe CLI wrapper utility to help customers sign with their private key

UEFI:

- DCSG00152527 - RSOD in UEFI environment during VMware 6.7, WMware 7.0 and RHEL 8.0 installs
- DCSG00217584 - Increase Stall() interval and reduce total number of loops accordingly

UEFI shell instructions for updating RAID Firmware:
- Download and extract all files to a USB flash drive.
- Boot the target system to EFI shell.
- Change directory to the local drive and directory containing the flash update files and the firmware image file.
- Type the name of the .nsh file matching the controller to update (e.g. "RMSP3HD080E.nsh" and press <Enter> to execute the command
- The storcli command line in the .nsh command will default to the first logical RAID contoller ("/c0"). If this there are multiple controllers, the value of controller parameter ("/Cx") will need to be modified to match the specific controller intended for update.
- Wait for the flash to complete. Do NOT reboot the system during the update.
- You can also use RAID Web Console 3 or OS version of StorCLI to update the RAID firmware.

Attention!

- Intel recommends to loading Factory Default setting after the firmware upgrade which will not affect data on any existing array.
- Reboot the system and login to the RAID BIOS Console.
- Select the controller and select 'Adapter Properties'->'Next'
- Set the 'Set Factory Defaults' setting to 'Yes' and submit the change.
- Reboot the system (the default settings are applied).
- Re-configure to the desired settings in RAID Web Console3.

Firmware downgrade notice

- Intel does not recommend to downgrade the factory installed firmware on your RAID module or controller, it has important enhancements and bug fixes you may lose when going to a previous version.
- If you need to install an older firmware version, please contact Intel for instructions on how to perform this action.

About SmartWatch Firmware:

Changing the SmartWatch's firmware version can increase its overall performance and stability, enhance various applications or improve their auto-update methods, as well as bring several other changes that might be useful for your device.

So if you consider applying this release, make sure you have read and understood the installation steps, and back up all your important files from the device.

As far as the update method is concerned, usually, you must get the downloadable package (extract it if necessary), transfer it to the SmartWatch through the available USB cable or via a compatible memory card, go to the setup menu's firmware upgrade section, and initiate the process.

Therefore, if you wish to upgrade your SmartWatch's firmware to this version, hit the download button and get the desired package. Moreover, don't forget to check with our website as often as possible in order to stay up to date with the latest releases.