This firmware incorporates all-new amp modeling algorithms:
- With this update the Axe-Fx II now incorporates our “Generation 3 (G3) Amp Modeling Technology”.
- G3 modeling improves upon our previous modeling with better touch sensitivity, better dynamics, better distortion texture (or “grain”) with less fizz, more crunch and improved frequency response accuracy.
- Not all amp models have been fully converted to take advantage of G3 modeling as of this release.
- Those that have been fully ported are indicated by “(G3)” after the model name on the Pre page of the Amp block.
- Those that have not been fully ported yet will still benefit from the improved algorithms.
The Rotary block has been completely revised:
- It is recommended to reset the block in any existing presets by double-clicking the Bypass button to load the default values.
- Also, the Rotary block now supports X/Y which simplifies slow/fast switching.
Added USB Return Level parameter to I/O->Audio menu:
- This parameter sets the level of the USB input sent to the main outputs.
Added “Word Clock” parameter to I/O->Audio menu:
- This selects the clock source for the A/D and D/A converters.
- Auto: uses the internal clock if the input source is Analog or USB. Uses the recovered SPDIF/AES clock if the input is SPDIF/AES.
- SPDIF/AES IN: uses the recovered clock for all input sources. A valid 48 kHz data stream must be present at the AES or SPDIF input. If a valid stream is not detected the unit will fall back to the internal clock and display "NO INPUT CLOCK!". The SPDIF/AES select must be set to the appropriate value, i.e. if the data stream is input to the XLR jack then SPDIF/AES SELECT must be set to AES.
Other Changes:
- Added modifier capability to Compressor block Level control
- Replaced some of the factory IRs with UltraRes IRs from our upcoming Universal Noise Storage 2 Cabinet Pack. These IRs are the first IRs that we have captured using the “Mic + DI” technique which results in IRs with improved accuracy and clarity.
- Fixed Cabinet block room simulation collapsing to mono if Mode is mono and Preamp Type is not None.
NOTE:
- It is possible that the new Word Clock parameter (see below) will be set to SPDIF/AES IN after installation of this firmware. This will result in a “NO INPUT CLOCK!” message appearing on the screen. If so, set the Word Clock value to “Auto” in the I/O->Audio menu.
- The USB Return Level parameter will be uninitialized after installation of this firmware. Set the desired USB Return Level via the I/O->Audio menu.
- CATEGORY:
- Firmware
- COMPATIBLE WITH:
- OS Independent
- file size:
- 4.4 MB
- filename:
- axefx2_18p01.zip
- Newer! Fractal Audio Axe-Fx II Mark II Preamplifier Firmware 19.002015-06-25
- Newer! Fractal Audio Axe-Fx II Mark II Preamplifier Firmware 18.082015-04-27
- Newer! Fractal Audio Axe-Fx II Mark II Preamplifier Firmware 18.02015-04-16
- Newer! Fractal Audio Axe-Fx II Mark II Preamplifier Firmware 18.062015-04-08
- Newer! Fractal Audio Axe-Fx II Mark II Preamplifier Firmware 18.042015-03-30
- Newer! Fractal Audio Axe-Fx II Mark II Preamplifier Firmware 18.032015-03-26
- Fractal Audio Axe-Fx II Mark II Preamplifier Firmware 18.012015-03-16
- Fractal Audio Axe-Fx II Mark II Preamplifier Firmware 17.042015-01-14
- Fractal Audio Axe-Fx II Mark II Preamplifier Firmware 17.002014-12-04
- Fractal Audio Axe-Fx II Mark II Preamplifier Firmware 16.04.12014-11-12