Integra DTR-70.1 A/V Receiver Firmware 1.10

Manufacturer:

Description

DOWNLOAD NOW

Changes:

- Increase the stability of network operations (Improves network operation when using the TCP/IP control)
- Improve the playback of some particular files (Corrects playback of mp3 files and some wav files may experience some noise)
- Improve the processing of DSD for output to Subwoofer (Corrects DSD 5.1 ch, Subwoofer volume level which is 10 dB higher than regular Direct mode)

Updating the Firmware:

- Connect a USB storage device to your PC. If there is any data in the USB storage, remove it.
- Download and unzip the firmware file
- Copy the extracted files to the USB storage device. Be careful not to copy the zip file.
- Remove the USB storage device from your PC and connect it to the USB port on the AV receiver/controller.
- When the AV receiver/controller has two USB ports, you can use either one.
- Make sure your AV receiver/controller and TV are turned on.
- If the AV receiver/controller is in standby mode, push [ON/STANDBY] to light up the front display.
- Select the USB input source. “Now Initializing” is displayed on the front display and then the name of the USB storage device is displayed. It will take 20 to 30 seconds to recognize the USB storage device.
- Push [RECEIVER] followed by [SETUP] on the remote controller.
- Main menu will be displayed on TV screen.
- Procedures thereafter can also be performed on the AV receiver/controller by using its SETUP, arrow, and ENTER buttons.
- Go to “7. Hardware Setup” menu.
- Go to “7-6. Firmware Update” menu.
- Select “Via USB” and push [ENTER].
- Select “Update” and push [ENTER]. Updating will begin.
- As the updating progresses, the TV screen may disappear depending on the program updated. In this case, you can see the update progress on the front display of the AV receiver/controller. The TV screen will reappear when you finish the update and turn on the AV receiver/controller.
- Do not turn off the AV receiver/controller and do not remove the USB storage device during updating process.
- Message “OK:Sum = ********” appears on the front display of the AV receiver/controller, indicating that the update has been completed. (Alpha-numeric characters on the front display are denoted by asterisks.)
- Using the [ON/STANDBY] button on the front panel, turn off the AV receiver/controller and then remove the USB storage device.
- Do not use the [ON] or [STANDBY] button on the remote controller.
- Push [ON/STANDBY] to turn on the AV receiver/controller.
- Congratulations!! Now you have the latest firmware on your Integra AV receiver/controller.

Precautions on the USB storage device:

- The storage media in the USB card reader may not work.
- If the storage device has been partitioned, each section will be treated as an independent device.
- If the USB mass storage device contains a lot of data, the AV receiver/controller may take a while to read it.
- Operation with all USB mass storage devices including the ability to power them is not guaranteed.
- Integra accepts no responsibility whatsoever for the loss or damage to data stored on a USB mass storage device when that device is used with the AV receiver/controller. We recommend that you back up your important music files beforehand.
- If you connect a USB hard disk drive to the USB port, we recommend that you use its AC adapter to power it.
- USB hubs and USB devices with hub functions are not supported. Do not connect your USB mass storage device via a USB hub.
- USB memory devices with security functions are not supported.

About A/V Receivers:

Each Audio-Video Receiver (A/V Receiver) is powered by a firmware version that enables all of its features and allows users to make the most of the device. Updating the firmware can bring various changes that should boost performance, such as improved compatibility with different multimedia file formats.

In order to do so, usually, you must transfer the firmware onto an empty USB storage device, connect the flash drive to the A/V Receiver, and initiate the upgrade process from the device’s setup menu.

However, this task must be carefully performed in a steady power environment, by someone who has completely read and understood all the installation steps or by a power user (recommended) – an update failure can cause your receiver's software to encounter serious malfunctions.

Therefore, if you think that this release can improve your audio-video receiver in any way, get the desired version through the available download button and apply the new firmware; if not, check with our website as often as possible so that you don’t miss the update that might improve your device.

Integra DTR-70.1 Firmware DTR-70.1 A/V Receiver Firmware Integra DTR-70.1 Preamplifier Firmware DTR-70.1 Firmware Integra A/V Receiver

  CATEGORY:
DVD / Blu-Ray / Media Players
  COMPATIBLE WITH:
OS Independent
  file size:
15.4 MB
  filename:
ONKAVR0001_H2H30000EIREHAHA_110.zip