Intel NUC RST Preinstall Driver 13.6.0.1002

  n/a
Manufacturer:

Description

DOWNLOAD NOW

Resolved Issues:

- IRST uninstaller doesn't require rebooting.

This download is valid for the products listed below:

- Intel NUC Board D34010WYB
- Intel NUC Board D54250WYB
- Intel NUC Board NUC5i3MYBE
- Intel NUC Board NUC5i5MYBE
- Intel NUC Kit D34010WYK
- Intel NUC Kit D54250WYK
- Intel NUC Kit NUC5i3MYHE
- Intel NUC Kit NUC5i3RYH
- Intel NUC Kit NUC5i3RYK
- Intel NUC Kit NUC5i5MYHE
- Intel NUC Kit NUC5i5RYH
- Intel NUC Kit NUC5i5RYK
- Intel NUC Kit NUC5i7RYH

Known Issues:

- The system displays two ODD icons after hotplug ODD
- Acceleration option not available when OS on SSD and PCIe SSD as pass through
- SUT goes to S5 abruptly during S4->S3->S4 cycle with RST caching config (Issue only with certain PCIe disk)
- Enabling SRT changes Device Manager Disk Drive Information
- BSoD 0xFC occur at F6 driver downgrade.
- RST 13.x drive returns wrong SSD model name if iSRT cache volume is created on it
- SUT takes more than 3 minutes to enter S4 under Win7.
- [HSW][SRT] 8.1 screen occurred when restart the unit after enable acceleration with full disk capacity on both Max/Enh modes
- System resume from S4 will hang up around few minutes issue with 2TB HDD
- Uninstaller screen words cut off in BRZL/PT(BZ) language Windows 7 with Resolution 1920X1080;125% DPI
- Driver: CE BSOD iastorA.sys occurs while uninstalling 13.5 on a 3rd Party Windows 8.1 OS
- UI - PCI-E SSD custom space defaults at 64 GB, even if the drive has less than 64 GB of space left
- SSD/HDD model name in Win7 Device Manager will be changed incorrectly after RST driver installed.
- UI: BSOD when clicking "Hide recovery disk files" actionable link with On request RRT Volume.
- UI: System drive is not displaying or being recognized in RST UI
- Iastor BSOD when auto rebuilding volume to the same port
- SRT filecopy performance much worse than HDD
- Sleep and PNP (disable and enable) with IO Before and After (Certification) on certain configurations
- UI Writeback Cache checkbox (Advanced tab) disabled during IRRT volume creation
- All expected TRIMs are not occurring on SRT
- "Offline" disk shows up as "Normal" after reinserting back into system while RAID 5(or RAID 10) is rebuilding and restarting system
- BSOD 9f occurs when certain PCIe-AHCI SSD is attached.
- After multiple iterations of Hybrid S3 or S4, the sleep utility tool indicates errors when RST driver is installed.
- OS Spindown of matrix RAID volumes causes hang
- SMART Event disk rebuilding after system reboot of successful Raid 1 creation
- internal_power_error (A0) BSOD with hybrid S3
- BSOD 0xD1 reported with inbox driver 12.0.1.1018
- No timeout for a device that does not enumerate and stalls the OS boot process
- Refresh issues when changing from Windows default theme to high contrast
- After configuring SRT and conducting Dirty Shutdowns error: Unable to find System Disk
- RST Driver – Test hangs while running Inquiry command on ODD
- SRT: Driver fails to enumerate an accelerated disk or volume during an F6 install if a system disk is already attached to the system
- UI reports Unknown status and incorrect sync mode after hot-removing the recovery disk of an IRRTm while the sync is initializing.
- WHQL: RST not compliant with Device.DevFund.Memory.DriverFootprint requirements for x86
- ZPODD power off timer does not reset upon receipt of CSMI I/O

About SATA / AHCI / RAID Preinstall Drivers:

Download this package if you intend to switch the SATA settings between available modes (AHCI, RAID, or IDE) after an operating system has been installed.

Remember that if you modify these settings without applying the proper files, the OS will not be able to boot until requirements are met or changes are reverted.

As for the installation method, it would be best if you refer to the manufacturer’s update guide, read all the steps, and initiate this task only when you have completely familiarized yourself with the procedure.

Even though other platforms might also be compatible with this release, we strongly recommend that you apply the driver only on specified operating systems in order to successfully perform the installation. If a failure occurs, the computer could suffer serious malfunctions.

With these in mind, if you wish to modify the SATA settings according to the mode highlighted in this version, click the download button and make the desired changes. Visit our website as often as possible to stay up to date with the latest releases.

Intel NUC Board RST Preinstall Driver Intel NUC Kit RST Preinstall Driver Intel NUC Rapid Storage Preinstall Driver NUC RST Preinstall Intel NUC Kit

  CATEGORY:
Motherboard
  COMPATIBLE WITH:
Windows 7
Windows 8
Windows 8.1
  file size:
534 KB
  filename:
STOR_Win7_8_8.1_13.6.0.1002_f6flpy-x86.zip
Other versions