EnGenius EAP300 Access Point Firmware 1.2.3

Business Class Indoor High-power Long-range 800mW Wireless-N Access Point/WDS/Repeater with Smoke Detector Housing & 802.3af PoE Support

Hardware Specifications
MCU/RF: RTL8196C + RTL8192CE
Memory: 32MB
Flash: 4MB
Physical Interface:
LAN: 1 x 10/100 Fast Ethernet RJ-45
Reset Button
Power Jack
LEDs Status
Power/Status
LAN (10/100Mpbs)
WLAN (Wireless connection)
Power Requirement:
Power Supply: 90 to 240 VDC ± 10%, 50/60 Hz
Active Ethernet (Power over Ethernet, IEEE802.3af)
48 VDC/0.375A
Device: 12V/1A

RF Specifications
Wireless Standard: IEEE802.11 b/g/n
Frequency: 2.400 ~ 2.484GHz (b/g/n)
Modulation Technologies:
OFDM: BPSK, QPSK, 16-QAM, 64-QAM
DBPSK, DQPSK, CCK
Operating Channels: 11 channels

Transmit Power:
802.11b(2.412 ~ 2.472 GHz)
26 dBm @ 1Mbps
26 dBm @ 2Mpbs
26 dBm @ 5.5Mbps
26 dBm @ 11Mbps

802.11g(2.412 ~ 2.472 GHz)
26 dBm @ 6Mbps
26 dBm @ 9Mbps
25 dBm @ 12Mbps
25 dBm @ 18Mbps
24 dBm @ 24Mbps
24 dBm @ 36Mbps
23 dBm @ 48Mbps
23 dBm @ 54Mbps

802.11n(2.412 ~ 2.472 GHz)
26 dBm @ MCS0/MCS8
26 dBm @ MCS1/MCS9
25 dBm @ MCS2/MCS10
25 dBm @ MCS3/MCS11
24 dBm @ MCS4/MCS12
24 dBm @ MCS5/MCS13
23 dBm @ MCS6/MCS14
23 dBm @ MCS7/MCS15

Receive Sensitivity:
802.11b (2.412 ~ 2.472 GHz) best ≤ -93 dBm
802.11g (2.412 ~ 2.472 GHz) best ≤ -90 dBm
802.11n (2.412 ~ 2.472 GHz) best ≤ -88 dBm

Antenna:
Embedded omnidirectional antenna (Diversity support)
Antenna Gain = 5 dBi

Software Specifications
Topology: Infrastructure/Ad-Hoc
Operation Mode: Access Point/WDS Bridge/WDS AP/Repeater
Multiple BSSID: Supports up to 4 BSSIDs
LAN Settings:
IP (check validity and DHCP server IP range)
MAC
DHCP range, lease time, client list
VLANs: Supports 802.1q (up to 4 VLANs)
SSID to VLAN mapping
Spanning Tree: Supports 802.1d Spanning Tree Protocol
Wireless mode: 11b/11g/11n
Channel selection (setting varies by country)
Channel bandwidth (Auto, 20MHz, 40MHz)
Transmission rate: 11n only, 11b/g/n mix, 11b only, 11b/g, 11g only
VPN: VPN pass-through (PPTP, L2TP, IPSEC)
QoS: WMM
WPS: Software only
Security: WEP Encryption - 64/128 bit
WPA Personal (WPA-PSK using TKIP or AES)
WPA Enterprise (WPA-EAP using TKIP)
802.1x Authenticator
SSID broadcast enable/disable
MAC Address Filter (AP mode)
WLAN L2 isolation (AP mode)
Wireless STA (Client) connected list (Idle/Connection Time, Pkt statistics)

Management
Tx Power Control: Adjust transmit power by dBm
Configuration: Web-based configuration (HTTP)/Telnet
Telnet Server: CLI
Firmware Upgrade: Upgrade firmware via web browser
Administrator Setting: Administrator Username & Password change
Reset Setting
Reboot (press 1 second). Reset to Factory Default (press 10 second)
System Monitoring: Status Statistic and Event log
SNMP: V1 , V2c
MIB: MIB I , MIB II(RFC1213) and Private MIB
Traffic Measurement: Per interface
Auto-channel Selection:
Automatically selecting least congested channel
Bandwidth Measurement:
IP range and bandwidth management
Backup & Restore:
Save & restore settings through Web interface
Diagnosis: IP pinging statistics

Environment & Physical
Temperature Range:
Operating: 0 to 50° C (32° to 122° F)
Storage: -20 to 60° C (-4° to 140° F)
Humidity (non-condensing):
Operating: 90% or less
Storage: 90% of less
Dimensions: Diameter: 4.73” (120mm)
Height: 1.97” (50mm)
Weight: 0.62 lb. (280g)
Certifications: FCC, CE, IC


It is highly recommended to always use the most recent driver version available.

Do not forget to check with our site as often as possible in order to stay updated on the latest drivers, software and games.

Try to set a system restore point before installing a device driver. This will help if you installed a wrong driver. Problems can arise when your hardware device is too old or not supported any longer.